Sound familiar?Toronto
- The call
- Someone smashed the little window beside the door, reached in and turned the thumb-turn. The lock itself is fine, but there is glass on the mat, a hole in the sidelight and a deadbolt anyone can reach.

There is a hole where the cylinder used to be. Somebody twisted it out of the deadbolt with a wrench, and now the empty bore looks straight through to the kitchen, with the bolt still stuck in the frame.
Most forced doors fail at the frame, not the lock. A standard strike plate is held by two short screws in a softwood jamb, and a kick transfers the whole force of a body to those screws. The bolt usually survives; the wood around it does not. Swapping the deadbolt for a heavier one leaves the weak point untouched, so a proper break-in repair rebuilds the strike side with a boxed strike, a pocket cut to full depth and three-inch screws that pass through the jamb and the shim space into the stud behind. The lock is replaced too, but the frame is where security returns.
Sound familiar?Toronto
Break-In Damage Lock Repair · Toronto

Scene 1
The damage tells the story of the attack, and the story decides the repair. A kick leaves the strike torn out and the jamb split along the grain, often with the deadbolt still thrown and intact. A pry bar leaves a crushed door edge, a bent latch and marks in the weatherstrip gap. A wrench attack twists the cylinder out of its housing and may shear the tailpiece, leaving a bolt stuck in the frame. Broken glass beside the door means the lock was never defeated at all; an arm simply reached the thumb-turn. Each pattern points to a different weak point, so identifying it first keeps the repair aimed at what actually gave way.
Scene 2
The strike is where most forced doors failed, so it is rebuilt rather than reattached. The old plate comes off and the bolt pocket is cut to full depth, since a pocket that is too shallow stops the bolt from extending completely and leaves it easier to push back. A security strike with a boxed pocket is set flush into the jamb, its long screws driven through the jamb and shim space into the wall stud, with the longest screws placed nearest the door stop where the bolt bears. Pilot holes are drilled first so the screws seat without splitting the repaired wood. The bolt now pushes against framing lumber instead of two short screws in soft trim.
Scene 3
You are left with a plain written account: which opening was forced, what was found damaged, what was replaced, what was reinforced and with what, which locks were rekeyed and how many keys were cut, and what remains for another trade. The photographs taken before work began sit alongside it. The broken hardware is bagged for the adjuster unless you say otherwise, and the receipt for the securing visit goes in the same folder, since insurers ask policyholders to keep damaged property and receipts. Together these turn a stressful evening into a claim file that answers questions before they are asked.
What shapes the quoteLeaside Lock Experts
FeesSame any hour
A large one. Factory strike and hinge screws are usually short enough to grip only the jamb, a piece of trim about an inch thick. Three-inch screws pass through the jamb and the gap behind it into the stud, so a blow has to move the wall rather than the trim. Lock manufacturers supply reinforcement plates with three-inch screws for exactly this reason, and note that a door beside a sidelight needs a different arrangement because glass sits where the stud would be.
Yes, unless the insurer has already said they are not needed. Insurers generally ask policyholders to retain damaged property until the claim is settled, and a bag holding the twisted cylinder, torn strike and split wood answers an adjuster's questions more clearly than any description. The locksmith hands them over at the end of the visit along with a written note of what was replaced. Photographs of the parts in place, before removal, complete the record.
Treat it as two exposures. The house key is handled by rekeying every lock it fits. The remote is handled at the garage door opener: its memory is erased so every old remote stops working, and new remotes are programmed. If the car had your address on its paperwork, do both before anything else. A locksmith can rekey the doors and, on many openers, clear the remotes during the same visit or show you the learn button on the motor unit.
TorontoOntario
Break-In Damage Lock Repair · Flemingdon Park, Leaside, Parkview Hill, Thorncliffe, Woodbine Heights
Every square is one home in a hundred.
On-site assessment
There is a hole where the cylinder used to be.
(289) 806-8979, open 24/7.
On-site assessment preferred · (289) 806-8979, open 24/7